-40%

16 Channel 12-bit PWM Servo Drive shield board -I2C PCA9685 For Arduino

$ 1.75

Availability: 242 in stock
  • Condition: New
  • Brand: Unbranded/Generic
  • UPC: Does Not Apply
  • MPN: Does Not Apply
  • All returns accepted: Returns Accepted
  • Item must be returned within: 60 Days
  • Restocking Fee: No
  • Return shipping will be paid by: Buyer
  • Refund will be given as: Money Back

    Description

    You want to make a cool robot, maybe a hexapod walker, or maybe just a piece of art with a lot of moving parts. Or maybe you want to drive a lot of LEDs with precise PWM output. Then you realize that your microcontroller has a limited number of PWM outputs! What now?
    Using only two pins, control 16 free-running PWM outputs! You can even chain up 62 breakouts to control up to 992 PWM outputs
    • It's an i2c-controlled PWM driver with a built in clock. That means that, unlike the TLC5940 family, you do not need to continuously send it signal tying up your microcontroller, its completely free running!
    • It is 5V compliant, which means you can control it from a 3.3V microcontroller and still safely drive up to 6V outputs (this is good for when you want to control white or blue LEDs with 3.4+ forward voltages)
    • 6 address select pins so you can wire up to 62 of these on a single i2c bus, a total of 992 outputs - that's a lot of servos or LEDs
    • Adjustable frequency PWM up to about 1.6 KHz
    • 12-bit resolution for each output - for servos, that means about 4us resolution at 60Hz update rate
    • Configurable push-pull or open-drain output
    • Output enable pin to quickly disable all the outputs
    We wrapped up this lovely chip into a breakout board with a couple nice extras
    • Terminal block for power input (or you can use the 0.1" breakouts on the side)
    • Reverse polarity protection on the terminal block input
    • Green power-good LED
    • 3 pin connectors in groups of 4 so you can plug in 16 servos at once (Servo plugs are slightly wider than 0.1" so you can only stack 4 next to each other on 0.1" header
    • "Chain-able" design
    • A spot to place a big capacitor on the V+ line (in case you need it)
    • 330 ohm series resistors on all the output lines to protect them, and to make driving LEDs trivial
    • Solder jumpers for the 6 address select pins
    Package Included:
    1 x New 16-Channel 12-bit PWM/Servo Driver -I2C PCA9685 For Arduino
    Payment
    Payment
    Payable To
    Note
    PayPal
    Paypal
    All payments are due within 7 days of the close of auction. Failing to do so, non-paying bidders will be reported to eBay.
    Shipping Policy
    Delivery Time
    We ship to worldwide, it usually takes 10-30 Business Days to delivery.
    Shipping address
    We ship to your PayPal address. Please, make sure to provide us with correct, precise, and detailed shipping Address.
    Send Time
    Items will be shipped within 1 to 3 business days upon payment received or cleared.
    Note
    If you don't receive items over 30 business days, please notify us via eBay message.
    Return Policy
    We appreciate your business and offer an instant 7 days return policy.(7 days after receive the item). The returned item has to be in its original condition. We are able to refund your money without shipping cost.
    Contact us
    For anything about product, price, shipping or order status, please contact us via eBay message.
    We love positive feedback and 5 scores DSR. We will leave it for everyone that leaves it for us.